-
jay1981 [TS]
on
11 Feb 13 @ 09:41 AM #
Hi mga Sir,pa help naman po.masakit na ulo ko dito..meron po kami PLDT ZyXEL P-660HN-T1 ,ung modem router ng pldt ngaun,ang problema ko po is paano mag add ng isa pang wireless router para po sa isang kwarto naman na di na naabot nung ZyXEL P-660HN-T1.Bumili po kasi ako tapos tama naman ung cabling ko,pero ayaw pa din gumana,di po dapat plug and play lang itong binili kong wireless router(asus rt-n10lx)PLS HELP PO.
-
seymorebutts
on
11 Feb 13 @ 10:02 AM #
disable dhcp sa new router mo
-
jay1981 [TS]
on
11 Feb 13 @ 10:09 AM #
Sir pasensya na po,san po ba makikita un at ano po ung dhcp,maraming salamat po
-
jay1981 [TS]
on
11 Feb 13 @ 10:36 AM #
sir napasok ko na po ung router kong bago,wala naman po akong nakitang dhcp.ty
-
rayback
on
11 Feb 13 @ 10:46 AM #
^
wag mu sa WAN ng bagong wireless mu ikabit yung cable, sa LAN port.
para maging access point / switch lang sya totally.
tama, disable mu DHCP server para sa zyxel dhcp service and ip addressing.
...
-
networm
on
11 Feb 13 @ 11:01 AM #
First, configure your Router so that DHCP is disabled...
Once configured and DHCP is disabled...
Do NOT use the WAN Port of the router.
Use any of the LAN port to connect it to the PLDT DSL modem.
This connection/configuration allows your Asus router to act as an AP(Access Point). That way, there will be no conflicts in IP addresses, specially if you have a printer and file sharing setup at home.
-- edited by networm on Feb 11 2013, 11:09 AM
-
jay1981 [TS]
on
11 Feb 13 @ 03:10 PM #
sir my kelangan pa po ba akong baguhin sa IP pag ginawa ko ito?salamat
-
striker2413
on
11 Feb 13 @ 03:16 PM #
wala kang gagalawin sa zyxel router mo..
i-connect mo yung LAN port ng zyxel mo sa WAN port ng wireless router mo, then enable mo yung BRIDGED MODE ng wireless router mo. DONE!
-applicable only pag yung wireless router mo lang yung gagamitin. otherwise, follow the steps above
-- edited by striker2413 on Feb 11 2013, 03:22 PM
-
Blu3martini
on
03 Mar 13 @ 12:11 PM #
wala kang gagalawin sa zyxel router mo..
i-connect mo yung LAN port ng zyxel mo sa WAN port ng wireless router mo, then enable mo yung BRIDGED MODE ng wireless router mo. DONE!
-applicable only pag yung wireless router mo lang yung gagamitin. otherwise, follow the steps above
-- edited by striker2413 on Feb 11 2013, 03:22 PM
Thread resurrection jutsu
Incomplete yung guide mo, hindi gagana yan
Notice to all users of Zyxel P660HN-T1A crap modem.
After talking with my cousin he gave me 20mins of internet downtime so I can test bridge mode on it.
<click here for link>
Refet to this PDF guide for switching to bridge mode; I have tested it personally and it works!
Summary
Go to Page 34 of the PDF manual
Set a static IP of
192.168.1.100
255.255.255.0
192.168.1.1
login to 192.168.1.1
adminpldt
1234567890
Do the steps on page 38
Bridge
RFC1483
VPI 0
VCI 100
Save
Now this is where it differs from the usual bridge mode.
Step 1 Disable Wifi
Step 2 Disable DHCP server
Step 3 Set LAN IP to 192.168.1.1
Step 4 remove all LAN devices
Step 5 Save and reboot
Step 6 connect LAN cable to Wifi Router WAN(Any port from Modem will do)
Do not connect additional devices or remove this connection between the Modem and the Wifi Router, you'll lose connection and have to restart it.
If you're not convinced I can post an image of the Zyxel P660 t1a+screenshot in the GUI with IP address.
With sir motion55's guide for flashing the Prolink 5004n and my post for setting this to bridge mode, There is no longer a need to replace modems.
-- edited by Blu3martini on Mar 03 2013, 12:16 PM
-
ryannapsters
on
18 Apr 14 @ 03:44 PM #
sir tanong ko lang po paano ko po mababawasan ung distribute ng internet sa wireless kasi ung lan ko 100m ung wireless 150m kapag naglalaro ako sa desktop ko tapos may nagconnect na tablet or wireless nahihigop nya ung internet..
-
glsantos
on
15 Apr 16 @ 09:00 PM #
guys pa-check naman current modem settings ko kung tama, ngayon ko pa lang nagamit itong zyxel p-660hn-t1a. or ano ba need ko i-update sa advanced setup. thanks
ADSL Mode : Auto Sycn-up
Annex Type : ANNEX A/L
Mode : Routing
Encapsulation : ENET ENCAP
Multiplex : LLC
Virtual Circuit ID
VPI : 0
VCI : 100
Bridge Interface Deactivated
