NZXT Kraken

• dulber on 20 Nov 13 @ 08:53 PM #

  Nice.
  Kraken Control version 1.6 installed successfully
  Software is now working and I have control of all aspects of the cooler
  Hindi lang binabalik yung RPM ng fans for some reason baka kelangan sa unang connectors nakakabit fans
  
  Wire tuck muna then picture picture ng rig then experiment sa ibang fan placements
  Stock placement ng fans as indicated in the instructions - sandwiched between case and rad
  Thank you NZXT for a swift (in my experience) resolution

• dulber on 23 Nov 13 @ 03:00 AM #

  push-pull fans config with working Kraken Control software (minus the fans rpm reading)
  
  
  
  push fans NZXT FZ 140mm LED white (non-PWM)
  pull fans stock Kraken PWM 140mm
  
  without flash
  
  
  
  The rear exhaust fan is a Scythe 120x12mm Slip Stream slim
  Hindi kasya 25mm thick fan sa lapit ng tubes
  Maski itong 12mm tinutulak ng tubes kaya for the photo nilagyan ko muna zip tie tubes to make the fan rotate
  current set-up may stove type fan grill na yung Scythe (updated photos to follow)
  
  Umuubra na Kraken control profiles (Silent, Custom, Extreme) kahit hindi PWM fans yung push
  Kelangan lang PWM-nonPWM-PWM-nonPWM ang pagkasaksak sa fan bus ng Kraken
  experiment pa ako para mapalabas fans rpm
  
  Ang isang issue ko ngayon sa unang bukas ng PC walang CPU temp sa Kraken Control
  Hindi nabubuhay yung Open Hardware Monitor automatically kasama ng Kraken Control
  Troubleshoot pa konti

• lpdr0k on 15 May 14 @ 08:35 PM #

  hello, i just installed my kraken x60. pump seems to be running, the led is on, and all is well.
  
  but i simply cannot get the kraken control software to detect the x60
  
  *note: i am not concerned with the issue of the kraken x60 not displaying cpu temps, i have found a supposed solution to this problem*
  
  what i specicfically am concerned with is getting the x60 detected, and/or detected by \'kraken control\'
  
  motherboard: 990fx sabertooth r2.0
  OS: windows 7 ultimate 64bit
  
  i have tried:
  
  -updating my bios to the latest one (v2501, i even learned how to bios flashback, lol.)
  -tried installing on both the usb headers, restarting after the install on both
  -transferring the 3pin of the kraken from the cpu_fan to the cpu_opt
  -removed all,fans on the x60 splitter, but the two pwm nzxt fans
  -tried installing khuler chill control V version 1.2 (still did not detect the x60)
  -using the stock 1.1 version of kraken control from the cd that came with it
  -using the 1.6 version of kraken control from nzxt website
  
  still no luck.
  
  
  really need suggestions,
  thanks in advance
  
  -- edited by lpdr0k on May 15 2014, 08:59 PM

• dulber on 16 May 14 @ 01:37 PM #

  that\'s interesting
  na check mo na sir kung may kelangan enable sa USB mobo headers mo sa BIOS?
  I suppose after you updated the BIOS you set it to optimal settings first then checked?

• dulber on 16 Jun 14 @ 11:08 PM #

  X61 introduced along with the revised CAM software
  Now taking the CAM software for a spin
  
  Antay nung new 140mm PWM V2 fan for more performance on the old X60

• marcski07 on 26 Jul 14 @ 02:29 AM #

  hello ask ko lng, kasi balak kong bumili ng 200mm fans, pero wala nmn available na pwm/4pin 200mm fans, pero hindi nmn importante un, ang concern ko lng, pwede ko bang i-connect un sa 4pin fan header ng kraken (ung apat na connector na naka chain, tapos ung nakakonect sa mobo is ung usb connector) ung 3pin 200mm fan na bibilhin ko?

• dulber on 26 Jul 14 @ 06:00 PM #

  aandar pero sasabay sa settings ng NZXT software
  sagad RPM niyan malamang kung low speed silent fan ang gamit mo
  kung high speed naman sigurado maingay
  
  I once connected a Corsair PF 120mm to the chain
  ayun full speed at super ingay. hindi kasi umabot power cable sa mobo header
  nabilhan ko na ng extension at tahimik na buhay ngayon

• marcski07 on 30 Jul 14 @ 09:22 AM #

  how do you mean sagad? dba na se-set-up naman un sa nzxt kraken software ung fan speed? para hindi 100% rpm? saka pwede ba gamitin ung CAM software sa old kraken?

• marcski07 on 30 Jul 14 @ 09:22 AM #

  how do you mean sagad? dba na se-set-up naman un sa nzxt kraken software ung fan speed? para hindi 100% rpm? saka pwede ba gamitin ung CAM software sa old kraken?

• dulber on 30 Jul 14 @ 01:13 PM #

  sinubok ko first version ng CAM hindi umubra
  yung new version mukhang specific pa lang sa X61 & X41
  
  sagad meaning mataas agad fan speed nung Corsair 120mm
  judging from the noise it was making, for some reason ayaw niya sumabay
  sa set-up ng controller
  
  ibinalik ko na ulit sa mobo header after makabili ng extension 3-pin cable
  tahimik na ulit mundo ko
  
  nakapag re-install na din ako ng Win8.1 pero quirky pa din
  hindi ko ma perfect itong install ng Win8 although pangalawa pa lang ito at
  hindi clean install dahil upgrade lang license ko
  
  nakikita ni Win8 yung device pero hindi niya makilala na USB device sa una
  hulaan pa kung anong device yun unlike yung ibang devices kahit wireless
  madaling makita na HID device, eto sablay, eh

• sickpig on 17 Aug 14 @ 01:49 PM #

  Hello Fellow NZXT Kraken users.. May problema po yung kraken ko.
  
  Nasira yung mobo ko nung Friday parehas ng bumigay yung GPU slot nya, kaya nag decide ako bumili ng mobo nung Saturday kahapon.. Yung mobo ko ngayon mga sir ay MSI 970 gaming. Nung sa luma kong mobo at setup, ok naman hindi naman nag overheat yung ProcIC.. Nung nag kinabit ko na sa bagong mobo, nag overheat yung ProcIC namamatay kapag 110`C na.. ang bilis tumaas ng temp, mga 30sec - 1minute mag 110`C na siya.. tapos pag hinawakan ko yung tubo mainit yung isang tubo yung isa hindi..
  
  iniisip ko baka hindi gumagana yung pump.. pag hinawakan ko naman yung pump may vibrations naman, di ko lang alam kung galing sa pump mismo o vibrations ng fan yun.. dalawang beses na akong nag tanggal kabit baka hindi lapat yung pag kabit ko pero ok naman, same as before naman pag lalagay ko.. saka may thermal paste akong nilalagay, china nga lang na mumurahin pero nag try ako ng dalawang brand.. yung isang brand ok naman sa i5 ng utol ko..
  
  Baka po may experience kayo or may troubleshooting steps na pwedeng gawin.. Please advise nalang po.. salamat po!

• raven1322 on 23 Jul 15 @ 03:02 PM #

  hello guys, ask ko lang po sana san may available na kraken x41 na alam nyo within NCR. wala na kasi ako makita dito sa tpc or anywhere. phase out po ba sya? thanks!

• dulber on 24 Jul 15 @ 03:39 PM #

  Hindi sikat Kraken maski sa TPC eh. Best to search local distro from their site then contact them for retailers. Otherwise Amazon na at ibang equivalent sellers na lang katapat

• dulber on 13 Aug 15 @ 10:48 PM #

  I have to give NZXT props for making the CAM software work with the Kraken X60 despite being discontinued for some time
  And it works very well with Windows 10 Pro, too
  I\'m impressed
  
  
  
  Next stop try to access the thing from the Internet on my mobile device

• ramcatimugan1990 on 01 Sep 15 @ 07:43 PM #

  also interested on Kraken X41. Planning on upgrading and adding 2 more ram sa rig ko kaya lang natatakpan ung slots nung EVO ko. Sana iport na nila dito ung x41

• keevinviray on 03 Sep 15 @ 02:05 PM #

  May alam po ba kayo kung saan may stock pa ng NZXT Kraken X61?

• dulber on 05 Sep 15 @ 05:09 PM #

  search mo lang dito boss kraken x61 may maihigit limang hits pili ka lang dun malapit sa iyo