Q9550 Official thread

• paul100800 on August 20, 2010 12:52 AM

  ^Parehas lang naman din sir. Naiba lang yung pangalan at setup ng bios pero ganun din naman mag-OC.
  
  Try mo muna sir yung settings na binigay ko.

• Nerdy777 on August 20, 2010 01:02 AM

  @paul
  
  ok ok...nga pala papaano ko malalaman sa OCCT kung stable na OC ko?...
  
  kasi nagDOWNLOAD ako nga pala eto current setting ko:
  
  Main page:
  AC shutdown - Enabled
  O.C. Fail retry counter - 1
  O.C. Fail CMOS reload - Disabled
  CPU Clock Ratio - 8.5x
  CPU N/2 Ratio - Enabled
  TArget CPU CLock - 3400mhz
  CPU Clock - 400mhz
  DRAM SPeed - 333/800
  Target DRAM Speed - DDR2 960
  PCIE Clock - 100mhz
  CPU Spectrum - Disabled
  PCIE Spread Specctrum - Disabled
  
  CPU Feature page:
  Thermal Management Control - Enabled
  PPM (EIST) Mode - Disabled
  Limit CPUID Max - Disabled
  C1E Function - Disabled
  Execute Disable Bit - Disabled
  Virt Technology - Disabled
  Core Mult Processing - Enabled
  
  DRAM settings:
  CAS Latency - 5
  RAS # CAS # - 5
  RAS# Precharge - 5
  Precharge Delay - 15
  All Precharge to Act - 6
  Ref to Act Delay - 60
  Write to Pre Delay - 22
  Rank Write to Read - 19
  Act to Act Delay - 8
  Read CAS # Percentage - Auto
  All Pre to Refresh - Auto
  
  Voltages:
  CPU VID Special Add - +125.0mv
  DRAM Voltage Control - 2.100
  SB Core/CPU PLL Voltage - 1.55v
  NB Core Voltage - 1.3200
  CPU CTT Voltage - 1.30v
  VCore Droop Control - Enabled
  Clockgen Voltage Control - 3.45v
  CPU GTL 0/2 REf Volt - 0.67x
  CPU GTL 1/3 Ref Volt - 0.67x
  North Bridge GTL REf Volt - 0.67x
  FSB Vref - 2A
  
  CPU Core - 1.16
  DRAM - 2.09
  NB Core - 1.29
  CPU VTT - 1.28
  
  pabigay naman po suggestion kung ano po mali..kasi pag hindi naka OC yung CPU ko nakakapaglaro ako nang starcraft 2..pag naka OC nagcacrash...
  
  then pag 3D rendering naman nagsstop..pag d naka OC tuloy tuloy lang..nagtataka lang me..T_T

• paul100800 on August 20, 2010 01:18 AM

  Main page:
  AC shutdown - Enabled
  O.C. Fail retry counter - 1
  O.C. Fail CMOS reload - Disabled
  CPU Clock Ratio - 8.5x
  CPU N/2 Ratio - Enabled
  Target CPU Clock - 3400mhz
  CPU Clock - 400mhz
  DRAM Speed - 333/800<<<<<<<<<Adjust mo to
  Target DRAM Speed - DDR2 960<<<Para maging 1066 nakalagay dito
  PCIE Clock - 100mhz
  CPU Spectrum - Disabled
  PCIE Spread Spectrum - Disabled
  
  CPU Feature page:
  Thermal Management Control - Enabled
  PPM (EIST) Mode - Disabled
  Limit CPUID Max - Disabled
  C1E Function - Disabled
  Execute Disable Bit - Disabled
  Virt Technology - Disabled
  Core Mult Processing - Enabled
  
  DRAM settings:
  CAS Latency - 5
  RAS # CAS # - 5
  RAS# Precharge - 5
  Precharge Delay - 15
  All Precharge to Act - 6
  Ref to Act Delay - 60
  Write to Pre Delay - 22
  Rank Write to Read - 19
  Act to Act Delay - 8
  Read CAS # Percentage - Auto
  All Pre to Refresh - Auto
  
  Voltages:
  CPU VID Special Add - +125.0mv<<<<<<Mataas to masyado, bawasan mo
  DRAM Voltage Control - 2.100
  SB Core/CPU PLL Voltage - 1.55v<<<<<<1.5V lang
  NB Core Voltage - 1.3200<<<<<<<<<<<1.24V lang
  CPU VTT Voltage - 1.30v<<<<<<<<<<<<1.21v
  VCore Droop Control - Enabled<<<<<<<Disable mo
  Clockgen Voltage Control - 3.45v
  CPU GTL 0/2 REf Volt - 0.67x
  CPU GTL 1/3 Ref Volt - 0.67x
  North Bridge GTL REf Volt - 0.67x
  FSB Vref - 2A
  
  CPU Core - 1.16
  DRAM - 2.09
  NB Core - 1.29
  CPU VTT - 1.28

• Nerdy777 on August 20, 2010 01:36 AM

  @paul
  
  sir sa southbridge >> default voltage po yan
  
  sa NB naman..1.24 yan yung default so binago ko sya...
  
  sa Dram timing naman..walang ibang way para maging 1066 mhz...yung ratio kahit saan ko ilagay..T_T

• paul100800 on August 20, 2010 01:04 PM

  Yung sa NB okay na yung default nya. Mataas na din. Basta lagay mo sa 1.24V, wag mo lagay sa auto.
  
  Yung sa timing hindi ko alam kung bakit wala yan. Kung malapit lang yan, Ako na nag-OC nyan. Hehe...
  
  try mo muna sa auto yung DRAN speed. Baka sakali mag-1066 dun.

• Nerdy777 on August 20, 2010 09:54 PM

  @paul
  
  hehehe waw..taga saan po ba kayo sir?...
  
  
  hindi na nakaauto
  
  ang nakakatwa pa minsan pag nag OC ako ayaw mag install maayos nang mga iniinstall ko na programs laging may error
  
  pag tinanggal ko OC ayun nagtutuloy tuloy..ang labo sobra..T_T

• Nerdy777 on August 20, 2010 10:44 PM

  @paul
  
  btw sir..parang ayaw ko na itry galawin yung settings...
  
  baka masira e..bagong bago pa naman ito mobo...mahirap na..T_T
  
  baka lalong d namin magamit ni utol...anyway ayun salamat po sa pagaccomodate..tyaga tyaga nalang muna ako til makakita nang fit na mobo for my Q9550

• paul100800 on August 21, 2010 06:36 AM

  @Nerdy777
  
  QC po ako. Malamang hindi po stable yung OC kaya nagkakaproblema po sa installation.
  
  DFI have a good reputation as an OCing motherboard. Isa sa mataas mag-OC ng mobo.
  
  
  Anyway, its your choice po. Kung hindi pa naman kayo bitin sa performance ng Q9550,
  
  Hindi na po kailangan mag-OC. Malakas pa naman procie natin. Sakin lagi lang nasa stock.
  
  OC lang ako pag benchmark o pag trip ko lang minsan. Hehe... Pero never naman po ako
  
  nagkaproblema when it comes to installation pag naka-OC yung procie.
  
  
  Nasisira naman mobo pag overvolting, dun nasusunog yung mobo. Kaya po paisa-isang
  
  increment lang pag nag-aadjust ng voltage. But its better to be safe than sorry. Hehe...
  
  Pero in most cases na nasusunog yung mobo pag extreme OCing na ("not all but mostly").

• Nerdy777 on August 21, 2010 06:07 PM

  @paul
  
  ahh hehehe..hindi ko kasi alam settings dito papaano ayusin...
  
  gs2 ko sana...ipagawa sa marurunung
  
  talaga maappreciate ko kahit magabot ako nang kaunti..hindi naman kasi kami mayaman din..
  
  gs2 lang talaga namin mas madagdagan nang kaunti pa yung speed nang proce namin kesa magpalit kasi yun naman ang praktikal na way e..
  
  if in case avail kayo sir...baka pde magpasuyo hehe

• paul100800 on August 21, 2010 06:23 PM

  Walang problema basta po malapit lang samin. Hehe... Nagtataka lang po ako bakit walang DRAM speed ratio para maging 1066.
  
  Pwede po siguro 1:1 nalang ratio. Mawin mong 800 yung DRAM speed tapos tighten mo yung timings.

• yakiboy on August 21, 2010 06:33 PM

  @nerdy
  
  
  baka kulang sa voltage, text mo si marky para maconfigure nya ng maayos yan. or pag may time tom daan kami ni mark dyan.

• Nerdy777 on August 21, 2010 09:40 PM

  @yakiboy
  
  sige sige...hehehe hindi ako marunung mag OC e
  
  @paul
  
  wala talaga sir na option ganun pag naka auto lang nagiging 1066 333/667

• ahiyakano on August 29, 2010 06:57 PM

  <click here for link>
  guys nabasa nyo na to?? parang its not yet worth it for upgrade lalo na for games.....

• paul100800 on August 29, 2010 08:12 PM

  wala talaga sir na option ganun pag naka auto lang nagiging 1066 333/667

  
  
  Kung sa auto nag-1066 Sir. Okay na yun. Just make sure to set the timings.
  
  

  guys nabasa nyo na to?? parang its not yet worth it for upgrade lalo na for games.....

  
  
  Kung internet at gaming lang kagaya ko, not worth it pa talaga. Better invest on videocards nalang.
  
  Siguro pag may lumabas na ulit na bago after sandy bridge tsaka na ako mag-upgrade. Hehe...
  
  Pero syempre sa madaming pera at hardware enthusiast, hindi mo talaga mapipigilan i-test yung bago.

• ahiyakano on August 29, 2010 08:27 PM

  @paul
  oo nga sir eh... ive been waiting for these and expecting to upgrade after ng board exam sa nov. and hopefully makapasa and will reward myself with an upgrade hmmnn bahala na heheh...

• pbatacan on August 29, 2010 08:35 PM - User is Online

  mura ba ang q9550 @ 7900? already used

• paul100800 on August 29, 2010 08:40 PM

  @ahiyakano
  
  Nice upgrade sir pag natuloy balak mo.
  
  @pbacatan
  
  Kung ikukumpara mo sir sa iba, medyo mura na sir. Kasi kaya pa sa 9k kung tutuusin.
  
  Kung makakadiscount ka pa konti, mas okay. Pero tingin ko hindi na ibibigay pa ng mas
  
  mababa pa dyan sir.

• pbatacan on August 29, 2010 08:42 PM - User is Online

  ^
  hmmmm thanks. hehehe. mura pala talaga

• eros_betrayer on September 01, 2010 02:07 AM

  bakit ganyan si Intel, papalit-palit ng socket type? :( buti nalang naka Q9550 nako since last year. ;)

• Leshrock18 on September 01, 2010 09:40 AM

  Sir tanong ko lang kung OK lang ba yung Speed(Gflops) ng IBT magkakaiba, saka kung ano mas maganda mababa ba o over 50 yung gflops?
  
  
  

• shamrea_3 on September 01, 2010 10:07 AM

  the lower the better.. usually you have to take the average to determine your gflops.
  
  btw, different gflops for every process is OK

• Leshrock18 on September 01, 2010 10:32 AM

  Thanks sir shamrea_3! newbie sa overclocking eh.. hehe! sinubukan ko lang..

603 active users within the last 5 minutes, 352 members, 251 guests.
Our newest member is Neumn
Click here to see online members.