Dynagen users post here

• mark2aguilar on October 23, 2007 11:49 AM

  Thank you very much sir BrockLINX for the link... very much appreciated.

• tbgswh on November 02, 2007 02:14 AM

  up natin...

• BrockLINX on November 03, 2007 02:57 PM

  Mga gurus.. in dynagen dynamips..
  
  di ko mapagana yung frame relay sample give.
  
  I got this config
  
  
  # A Simple frame relay lab
  
  autostart = False
  
  [localhost]
  
  [[7200]]
  image = e:\Program Files\Dynamips\images\c7200-ik9o3s-mz[1].124-12c.bin
  npe = npe-400
  ram = 160
  idlepc = 0x60897964
  
  [[ROUTER R1]]
  s1/0 = F1 1
  s1/1 = R5 s1/1
  model = 7200
  
  [[ROUTER R2]]
  s1/0 = F1 2
  model = 7200
  
  [[ROUTER R3]]
  s1/0 = F1 3
  s1/1 = R4 s1/1
  model = 7200
  idlepc = 0x60897964
  
  [[ROUTER R4]]
  model = 7200
  
  [[FRSW F1]]
  1:102 = 2:201
  1:103 = 3:301
  2:203 = 3:302
  
  [[ROUTER R5]]
  model = 7200
  
  
  my routers in a frame.. is not working for the reason that it has no timing clock recieved from the framce switch ( F1 )..
  
  si F1 naman is unconsolable? dahil wala siyang port assigned.
  
  Or..
  
  it should be redesigned and put a L2/L3 device in replacement to F1? kanya nga lang gagawa ka pa ng frame routing sa config na ganun?
  
  should you have already tried this,, please share naman po.
  
  Thanks
  
  -- edited by BrockLINX on Nov 03 2007, 03:00 PM

• zerglings on November 03, 2007 10:40 PM

  hindi ko pa natry... subukan ko mamaya pag nagkatime ako...

• BrockLINX on November 04, 2007 12:22 AM

  Master zerglings di ba CCNP ka?
  
  Thanks for the try zerlings,, i guess my question is not intended for you...
  
  -- edited by BrockLINX on Nov 04 2007, 12:34 AM
  
  -- edited by BrockLINX on Nov 04 2007, 12:35 AM

• BrockLINX on November 04, 2007 01:30 AM

  @zerglings
  
  master zerglings if you mind if i can ask, before you start kung meron kang time master,, kasi you seem to be very familiar with frame relay networking? I got this very simple wonderings..
  
  suppose i got this on DYNAGEN or in a real router kasi marami ka router di ba sir sa bahay or sa work.
  
  R1(DTE) <-------------> FR(DCE) <--------------->R2(DTE)
  
  mag-coconfigure ka narin master ng FR.. i was wondering what would be the ID or interface? I am going to use on my FR going to R1 and R2?
  
  supposed you are in a LAB or using your dynagen dynamips
  
  Am I going to put an IP address into it or should i use the DLCI routing?
  
  
  
  Dapat ba yung FR interface ko ka-subnet ng DTE router ko?
  
  
  kasi master, di mo ma-eemulate yan kung wala yung mga specifics di ba master?

• zerglings on November 04, 2007 10:59 AM

  Master zerglings di ba CCNP ka?

  
  
  nope.... not yet... i can be CCNP if i want to but i am taking my time to understand it.. i don't want to be paper certified.. :)
  
  

  Thanks for the try zerlings,, i guess my question is not intended for you...

  
  
  forum is open for everyone to answer your question... i wanted to try your lab so i know what is going on...
  
  

  master zerglings if you mind if i can ask, before you start kung meron kang time master,, kasi you seem to be very familiar with frame relay networking? I got this very simple wonderings..
  
  suppose i got this on DYNAGEN or in a real router kasi marami ka router di ba sir sa bahay or sa work.
  
  R1(DTE) <-------------> FR(DCE) <--------------->R2(DTE)
  
  mag-coconfigure ka narin master ng FR.. i was wondering what would be the ID or interface? I am going to use on my FR going to R1 and R2?
  
  supposed you are in a LAB or using your dynagen dynamips
  
  Am I going to put an IP address into it or should i use the DLCI routing?
  
  
  
  Dapat ba yung FR interface ko ka-subnet ng DTE router ko?
  
  
  kasi master, di mo ma-eemulate yan kung wala yung mga specifics di ba master?

  
  
  i have 3 2500s and two 800 series routers (871 and 871W) but i haven't been using them... at work, we have more than 6100 routers...
  
  here's a sample configuration if you want to use a router as a Frame switch....
  
  hostname FRAME_SWITCH
  !
  !
  ip subnet-zero
  no ip domain-lookup
  frame-relay switching
  !
  !
  !
  interface Ethernet0
  no ip address
  no ip directed-broadcast
  shutdown
  !
  interface Serial0
  no ip address
  
  interface Serial1
  no ip address
  no ip directed-broadcast
  encapsulation frame-relay
  logging event subif-link-status
  logging event dlci-status-change
  clockrate 56000
  no frame-relay inverse-arp
  frame-relay intf-type dce
  frame-relay route 122 interface Serial2 221
  frame-relay route 123 interface Serial3 321
  !
  interface Serial2
  no ip address
  no ip directed-broadcast
  encapsulation frame-relay
  logging event subif-link-status
  logging event dlci-status-change
  clockrate 56000
  no frame-relay inverse-arp
  frame-relay intf-type dce
  frame-relay route 221 interface Serial1 122
  
  interface Serial3
  no ip address
  no ip directed-broadcast
  encapsulation frame-relay
  logging event subif-link-status
  logging event dlci-status-change
  clockrate 56000
  no frame-relay inverse-arp
  frame-relay intf-type dce
  frame-relay route 321 interface Serial1 123
  
  the bold letters are the ones that you're going to add in to your router that will be acting like a frame switch... so to answer your question, no you don't need to put an ip address to frame switch.. the ip address will be in the routers that you'll be using...
  
  sorry, i didn't have the time to try your lab with my dynagen today.. i had to buy winter jacket since it is about to snow here in IL... and i had to pick my friend up from the airport... hopefully, i'll be able to try your lab tomorrow... goodluck...
  
  -- edited by zerglings on Nov 04 2007, 02:13 PM

• BrockLINX on November 05, 2007 02:19 AM

  WOW thanks idol... padalhan mo naman kami ng snow hahahaha.

• zerglings on November 05, 2007 03:59 AM

  wag mo ako tawagin idol or master.. i am not worthy... idolin mo si smoothmooovz at si erwinsky.. sila ang mga master or dapat idolohin.. sila ang mga CCNP dito... at future CCIP si smoothmoovz

• zerglings on November 29, 2007 08:16 AM

  sa mga guru ng dynagen..
  
  mas maganda bang gawin yung idlepc pag ang mga routers eh nasa
  

  
  Router con0 is now available
  
  
  Press RETURN to get started.

  
  ???
  
  kasi pag nag idle na yung ibang routers eh biglang tumataas yung CPU utilization ko eh. kasi yung R4 ko ginagawa ko na lang frame relay switch eh isang configuration lang iyon tapos hindi ko na ginagalaw.

• egaoga on November 29, 2007 08:29 AM

  hmmm ... interesting =)

• catmik on January 19, 2008 12:46 AM

  up ko lang to ha..kesa gumawa pa ako ng isang thread dito ko na lng tanong..related naman eh..hehe..
  
  may naka-try na ba sa inyo gumamit ng gns3?alam nyo ba pano ung idle-pc dun?kasi na-ssave naman kapag kinuha ko idle pc pero 100% pa din cpu utilization ko..mukhang mas ok kasi ito gamitin eh..tnx

• jdajose on January 19, 2008 04:49 AM

  dba sa gns3 wla nang idle pc??? pero ako 256 lng memory ko kya isang router lng mpagana ko.. hahahahaha.. wla na bang pagasa 2ng pc ko maliban sa upgrade? hehehehe...
  
  may console naman sa gns3 dba?
  
  -- edited by jdajose on Jan 19 2008, 04:49 AM

• venerzky on January 19, 2008 05:25 AM

  may console sa gns3..
  
  may idlepc din sya sir..
  
  dapat 1gig or higher pa para mas ok..

• catmik on January 19, 2008 05:48 AM

  yup meron cia idlepc,ayaw nga lng gumana sakn..hehe
  
  working ba sa vista 32 or 64 bit ang dynagen??thanks
  
  -- edited by catmik on Jan 19 2008, 05:49 AM

• vhinvhin_06 on January 19, 2008 01:22 PM

  ccnas pahingi naman po ng link where can i download dynagen.. mukhang mali kasi ata un nadownload ko... inirase ko nalang...
  thanks po ng marami...

• zerglings on January 20, 2008 11:24 PM

  dynagen.org po sir

• spider88 on January 31, 2008 11:40 PM

  may naka-try na ba sa inyo gumamit ng gns3?alam nyo ba pano ung idle-pc dun?kasi na-ssave naman kapag kinuha ko idle pc pero 100% pa din cpu utilization ko..mukhang mas ok kasi ito gamitin eh..tnx

  
  
  Bago ko pa lang natatry itong gns3 at mukhang ayos naman pala kasi usage ng cpu ko eh sobrang baba. 3 router lang kasi gamit ko.
  
  
  

• venerzky on February 01, 2008 03:03 AM

  ok talaga yang gns3..yan din ang gamit ko dito sa office eh..7200 na ios ang gamit ko..

• AmdIntel on February 03, 2008 10:57 PM

  Paano po ba gumawa ng frame relay sa gns3?

• venerzky on February 04, 2008 02:40 AM

  i-connect mo yung routers dun s frame-relay switch.
  
  -- edited by venerzky on Feb 04 2008, 02:41 AM

• jdajose on February 04, 2008 05:21 AM

  hahahaha! nice explanation ,,hehehehe oo nga naman dapat connect mo sa frame relay switch para mkgwa ng frame relay sa gns3..hehehehe

• venerzky on February 04, 2008 06:24 AM

  hahahaha! nice explanation ,,hehehehe oo nga naman dapat connect mo sa frame relay switch para mkgwa ng frame relay sa gns3..hehehehe

  
  
  hehehe..
  
  pasaway ba..hehehe..
  
  yung frame-relay na switch i-configure mo para sa DLCI.

• benicio on August 03, 2008 06:08 PM

  wahihi..di ko magets gaano. up ko lang muna
  
  -- edited by benicio on Aug 03 2008, 06:09 PM

• densflo on May 15, 2009 08:25 PM

  guys.. help naman.. esp duon sa mga masters. Ive been using VPCS for pc emulation, but i need something more. Can somebody help me find resouces kung paano makokonect ang gns3 to a VM using virtual box? I tried google but pang unix host ung details. Can someone help kung paano ko macoconect? I want to try TFTP and dchp relay

1498 active users within the last 5 minutes, 954 members, 544 guests.
Our newest member is castro_11
Click here to see online members.